Marmitek SC9000 Uživatelská příručka Strana 35

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 44
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 34
EXTRA OPTIONS
35SAFEGUARD / TOTALGUARD
DISARMED: The system is switched off.
EMERGENCY ALARM:
The alarm has been triggered by a PANIC BUTTON on a remote control or a Marmitek SD10 Smoke Detector.
ALARM IN ZONE 3: (example with zone 3). The alarm has been triggered by the sensor in zone 3
(wireless sensor or emergency sensor).
11.4 Operate lights and equipment via an outside phone
1. Call your home number. The console will answer.
2. You will hear ‘Please enter PIN’. Enter your PIN code.
3. If your PIN is correct, you will hear ‘PIN accepted’. If your PIN is incorrect, you will hear ‘Error’.
4. Press 4 *: The Marmitek X-10 module with UnitCode 4 will be switched on. You will hear ‘4 ON’ to confirm.
5. Press 4 #: The Marmitek X-10 module with UnitCode 4 will be switched off. You will hear ‘4 OFF’ to confirm.
12.Changing the batteries
When used normally the batteries in sensors and remote controls last about a year. The life span of batteries does depend on how
often a sensor is activated.
Preferably use alkaline batteries, but never rechargeable batteries (rechargeable batteries are not strong enough and will go flat
within a few months, even when they are seldom used).
Console – 4xAA batteries
The emergency batteries in the console ensure that even during a power cut the entire system stays operational for another 12
hours (if there is no alarm).
If there is an alarm during a power cut, the console will not activate the siren to save battery power. The telephone dialler
works normally.
If there is a power cut and the emergency batteries are flat, all settings are stored, because these are programmed into a non-
volatile memory (EEPROM). The clock will need to be reset.
When you decide to turn off the security system for a longer period (e.g. renovation work), remove the batteries from the
console to avoid them going flat.
If the emergency batteries are empty or not installed, the BATTERY indicator on the console will flash.
If you open up the battery compartment to change the batteries, the word ‘TAMPER’ will be visible on the display. After
inserting the batteries and closing the compartment, enter your PIN code (factory settings 0000, see 8.3) to remove the word
‘TAMPER’.
Key Chain Remote Control KR21 – 2x CR2016 batteries
De KR21 wordt geleverd met volle batterijen. Wanneer de indicator op de KR21 zwak gaat branden, dienen de batterijen
vervangen te worden.
A new KR21 contains fully charged batteries. If the indicator light on the KR21 is not very bright, the batteries should be replaced.
Open the remote control (back) with your nails or a small screwdriver. Use CR2016, 3V lithium batteries (2x).
To retain the unique code for your remote control, the batteries need to be replaced within 30 seconds.
If after replacing the batteries the console does not respond to your remote control, press the ARM button on your remote
control for 4 seconds to reactivate the remote. Then release the button. You now need to reregister the remote control, using
the procedure described in 3.1.2.
When pressing the ARM button the LED should flash quickly a few times. When the LED lights up and stays lit, you need to
reactivate the KR21.
To avoid losing a memory space, you can remove the old code for your remote control from the memory (see 8.2).
20071_20090424_UG_SC9000_EN 30-07-2009 09:10 Pagina 35
Zobrazit stránku 34
1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 43 44

Komentáře k této Příručce

Žádné komentáře